Pasted Locally

From Exploitee.rs
Jump to navigationJump to search
[ 0.000000] Linux version 2.6.23.18-gc0a9a5fb (richard@sayan) (gcc version 4.1.2) #3 PREEMPT Sat Jul 31 15:32:56 PDT 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e801: 0000000000100000 - 000000002bc00000 (usable)
[ 0.000000] BIOS-e801: 000000002bc00000 - 0000000040000000 (reserved)
[ 0.000000] 700MB LOWMEM available.
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 179200
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 179200
[ 0.000000] DMI not present or invalid.
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:c0000000)
[ 0.000000] Built 1 zonelists in Zone order. Total pages: 177800
[ 0.000000] Kernel command line: androidboot.bootloader=4.016-g5c94b454 androidboot.serialno=XXXXXXXXXXXX root=/dev/mtdblock:boot mtdparts=intel_ce_nand:2m(mbr)ro,8m(cefdk)ro,2m(redboot)ro,2m(cefdk-config)ro,8m@16m(splash)ro,1m(fts)ro,20m(recovery),5m(kernel)ro,64m(boot)ro,384m(system)ro,520m(data),5m(keystore)ro,1m(bbt)ro androidboot.hardware=logitech_ka5 usb-storage.nodelay_bus_name=0000:01:0d.0
[ 0.000000] Unknown boot option `androidboot.serialno=XXXXXXXXXXXX': ignoring
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1199.036 MHz processor.
[ 2.338119] console [ttyS0] enabled
[ 4.195868] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 4.281177] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 4.382697] Memory: 704964k/716800k available (2607k kernel code, 10812k reserved, 945k data, 192k init, 0k highmem)
[ 4.508476] virtual kernel memory layout:
[ 4.508479] fixmap  : 0xffffa000 - 0xfffff000 ( 20 kB)
[ 4.508482] vmalloc : 0xac800000 - 0xffff8000 (1335 MB)
[ 4.508486] lowmem  : 0x80000000 - 0xabc00000 ( 700 MB)
[ 4.508489] .init : 0x8047c000 - 0x804ac000 ( 192 kB)
[ 4.508492] .data : 0x8038bc18 - 0x80478398 ( 945 kB)
[ 4.508495] .text : 0x80100000 - 0x8038bc18 (2607 kB)
[ 4.968091] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 5.064864] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 5.236399] Calibrating delay using timer specific routine.. 2402.32 BogoMIPS (lpj=4804646)
[ 5.336252] Mount-cache hash table entries: 512
[ 5.390498] monitor/mwait feature present.
[ 5.439373] using mwait in idle threads.
[ 5.486168] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 5.542318] CPU: L2 cache: 512K
[ 5.579771] Intel machine check architecture supported.
[ 5.642148] Intel machine check reporting enabled on CPU#0.
[ 5.708702] Compat vDSO mapped to ffffe000.
[ 5.758622] CPU: Intel(R) Atom(TM) CPU CE4150 @ 1.20GHz stepping 0a
[ 5.835565] Checking 'hlt' instruction... OK.
[ 5.903147] NET: Registered protocol family 16
[ 5.956427] PCI: Using configuration type 1
[ 6.006315] Setting up standard PCI resources
[ 6.060671] SCSI subsystem initialized
[ 6.105576] usbcore: registered new interface driver usbfs
[ 6.171166] usbcore: registered new interface driver hub
[ 6.234651] usbcore: registered new device driver usb
[ 6.295299] PCI: Probing PCI hardware
[ 6.354043] PCI: Bridge: 0000:00:01.0
[ 6.397719] Time: tsc clocksource has been installed.
[ 6.458041] IO window: disabled.
[ 6.498594] MEM window: c0000000-dfffffff
[ 6.548505] PREFETCH window: disabled.
[ 6.595339] NET: Registered protocol family 2
[ 6.685661] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 6.771097] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 6.860802] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 6.940180] TCP: Hash tables configured (established 131072 bind 65536)
[ 7.019158] TCP reno registered
[ 7.067163] IA-32 Microcode Update Driver: v1.14a <[email protected]>
[ 7.155132] ashmem: initialized
[ 7.198407] squashfs: version 3.4 (2008/08/26) Phillip Lougher
[ 7.268379] yaffs Jul 31 2010 15:32:35 Installing.
[ 7.326855] io scheduler noop registered
[ 7.373649] io scheduler anticipatory registered
[ 7.428756] io scheduler deadline registered
[ 7.479742] io scheduler cfq registered (default)
[ 7.540469] rtc: I/O resource 70 is not free.
[ 7.592517] Non-volatile memory driver v1.2
[ 7.642460] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 7.735076] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a GEN3_serial
[ 7.812069] serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a GEN3_serial
[ 7.889538] RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize
[ 7.979558] loop: module loaded
[ 8.017173] logger: created 64K log 'log_main'
[ 8.070237] logger: created 256K log 'log_events'
[ 8.126477] logger: created 64K log 'log_radio'
[ 8.180959] input: Logitech KA as /class/input/input0
[ 8.241235] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
[ 8.312968] Copyright (c) 1999-2006 Intel Corporation.
[ 8.399068] e1000: 0000:01:0c.0: e1000_probe: (PCI:33MHz:32-bit) 1c:6f:65:XX:XX:XX
[ 8.517284] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 8.599649] Linux video capture interface: v2.00
[ 8.655009] usbcore: registered new interface driver uvcvideo
[ 8.723618] USB Video Class driver (v0.1.0)
[ 8.773763] ahci 0000:01:0e.0: PORTS_IMPL is zero, forcing 0x3
[ 9.848283] ahci 0000:01:0e.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 9.944944] ahci 0000:01:0e.0: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part
[ 10.046187] scsi0 : ahci
[ 10.076474] scsi1 : ahci
[ 10.106748] ata1: SATA max UDMA/133 cmd 0xac826500 ctl 0x00000000 bmdma 0x00000000 irq 4
[ 10.203464] ata2: SATA max UDMA/133 cmd 0xac826580 ctl 0x00000000 bmdma 0x00000000 irq 4
[ 10.424759] Clocksource tsc unstable (delta = 420816103 ns)
[ 10.492812] Time: pit clocksource has been installed.
[ 10.725018] ata1: SATA link down (SStatus 4 SControl 300)
[ 11.101330] ata2: SATA link down (SStatus 4 SControl 300)
[ 11.166130] physmap platform flash device: 02000000 at c0000000
[ 11.237223] physmap-flash physmap-flash.0: map_probe failed
[ 11.303971] Intel CE4100 NAND controller driver, version 1.2
[ 11.371608] Defaulting to ONFI 1 timings
[ 11.419424] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
[ 11.521432] 13 cmdlinepart partitions found on MTD device intel_ce_nand
[ 11.600444] Creating 13 MTD partitions on "intel_ce_nand":
[ 11.665944] 0x00000000-0x00200000 : "mbr"
[ 11.714101] 0x00200000-0x00a00000 : "cefdk"
[ 11.764271] 0x00a00000-0x00c00000 : "redboot"
[ 11.816464] 0x00c00000-0x00e00000 : "cefdk-config"
[ 11.873872] 0x01000000-0x01800000 : "splash"
[ 11.925028] 0x01800000-0x01900000 : "fts"
[ 11.973078] 0x01900000-0x02d00000 : "recovery"
[ 12.026349] 0x02d00000-0x03200000 : "kernel"
[ 12.077580] 0x03200000-0x07200000 : "boot"
[ 12.126701] 0x07200000-0x1f200000 : "system"
[ 12.177917] mtdblock9: 1 bad block(s) found
[ 12.228061] 0x1f200000-0x3fa00000 : "data"
[ 12.277210] mtdblock10: 1 bad block(s) found
[ 12.328400] 0x3fa00000-0x3ff00000 : "keystore"
[ 12.381643] 0x3ff00000-0x40000000 : "bbt"
[ 12.429430] mtdblock12: 4 bad block(s) found
[ 12.480863] ehci_hcd 0000:01:0d.0: EHCI Host Controller
[ 12.543428] ehci_hcd 0000:01:0d.0: new USB bus registered, assigned bus number 1
[ 12.654638] ehci_hcd 0000:01:0d.0: irq 4, io mem 0xdf810100
[ 12.730694] ehci_hcd 0000:01:0d.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[ 12.820482] usb usb1: configuration #1 chosen from 1 choice
[ 12.887077] hub 1-0:1.0: USB hub found
[ 12.931796] hub 1-0:1.0: 1 port detected
[ 13.079279] ehci_hcd 0000:01:0d.1: EHCI Host Controller
[ 13.141728] ehci_hcd 0000:01:0d.1: new USB bus registered, assigned bus number 2
[ 13.251144] ehci_hcd 0000:01:0d.1: irq 4, io mem 0xdf820100
[ 13.327193] ehci_hcd 0000:01:0d.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[ 13.416843] usb usb2: configuration #1 chosen from 1 choice
[ 13.483447] hub 2-0:1.0: USB hub found
[ 13.528163] hub 2-0:1.0: 1 port detected
[ 13.675730] Initializing USB Mass Storage driver...
[ 13.799593] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 14.016914] usb 1-1: configuration #1 chosen from 1 choice
[ 14.320027] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 14.533959] usb 2-1: configuration #1 chosen from 1 choice
[ 14.599845] hub 2-1:1.0: USB hub found
[ 14.644907] hub 2-1:1.0: 4 ports detected
[ 14.796782] scsi2 : SCSI emulation for USB Mass Storage devices
[ 14.891191] scsi 2:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 15.165086] usb 2-1.4: new full speed USB device using ehci_hcd and address 3
[ 15.340623] usb 2-1.4: configuration #1 chosen from 1 choice
[ 15.409902] sd 2:0:0:0: [sda] 7831552 512-byte hardware sectors (4010 MB)
[ 15.491164] usbcore: registered new interface driver usb-storage
[ 15.562901] USB Mass Storage support registered.
[ 15.618249] sd 2:0:0:0: [sda] Write Protect is off
[ 15.675407] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 15.748280] usbcore: registered new interface driver usbserial
[ 15.818034] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[ 15.912800] usbcore: registered new interface driver usbserial_generic
[ 15.990782] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[ 16.065728] drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
[ 16.176088] usbcore: registered new interface driver ftdi_sio
[ 16.244723] drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
[ 16.337097] i8042.c: No controller found.
[ 16.385060] mice: PS/2 mouse device common for all mice
[ 16.449530] sd 2:0:0:0: [sda] 7831552 512-byte hardware sectors (4010 MB)
[ 16.532095] sd 2:0:0:0: [sda] Write Protect is off
[ 16.589239] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 16.662038] sda:<6>rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 16.747248] Fixing bogus CMOS RTC mode
[ 16.792045] rtc0: alarms up to one day
[ 16.836989] usbcore: registered new interface driver hiddev
[ 16.903584] sda1 sda2
[ 16.931966] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 16.999515] input: Logitech USB Receiver as /class/input/input1
[ 17.090534] input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:01:0d.1-1.4
[ 17.199588] input: Logitech USB Receiver as /class/input/input2
[ 17.294860] input,hiddev96,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:01:0d.1-1.4
[ 17.410249] hiddev97hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:01:0d.1-1.4
[ 17.516298] usbcore: registered new interface driver usbhid
[ 17.582832] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 17.657778] oprofile: using timer interrupt.
[ 17.708880] nf_conntrack version 0.5.0 (11264 buckets, 45056 max)
[ 17.782089] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.845534] TCP cubic registered
[ 17.883981] Initializing XFRM netlink socket
[ 17.934967] NET: Registered protocol family 1
[ 17.987293] NET: Registered protocol family 10
[ 18.040432] lo: Disabled Privacy Extensions
[ 18.090379] Mobile IPv6
[ 18.119510] IPv6 over IPv4 tunneling driver
[ 18.169629] sit0: Disabled Privacy Extensions
[ 18.221834] NET: Registered protocol family 17
[ 18.274879] NET: Registered protocol family 15
[ 18.327986] Using IPI Shortcut mode
[ 18.443864] fts: v28 loaded from 0x00088000
[ 18.493966] rtc_cmos rtc_cmos: setting the system clock to 2009-01-01 00:00:02 (1230768002)
[ 18.595638] VFS: Mounted root (squashfs filesystem) readonly.
[ 18.664506] Freeing unused kernel memory: 192k freed
[ 18.924439] yaffs: dev is 32505865 name is "mtdblock9"
[ 18.985831] yaffs: passed flags ""
[ 19.026382] yaffs: Attempting MTD mount on 31.9, "mtdblock9"
[ 19.109736] yaffs: restored from checkpoint
[ 19.159644] yaffs_read_super: isCheckpointed 1
[ 19.212998] yaffs: dev is 32505866 name is "mtdblock10"
[ 19.275333] yaffs: passed flags ""
[ 19.315882] yaffs: Attempting MTD mount on 31.10, "mtdblock10"
[ 19.530105] block 414 is bad
[ 20.299577] yaffs_read_super: isCheckpointed 0
[ 20.352805] yaffs: dev is 32505867 name is "mtdblock11"
[ 20.415137] yaffs: passed flags ""
[ 20.455688] yaffs: Attempting MTD mount on 31.11, "mtdblock11"
[ 20.526148] yaffs: restored from checkpoint
[ 20.576013] yaffs_read_super: isCheckpointed 1

e2fsck 1.41.0 (10-Jul-2008) /dev/sda1: recovering journal /dev/sda1: clean, 12/32960 files, 6281/131656 blocks

[ 20.872514] kjournald starting. Commit interval 5 seconds
[ 20.943842] EXT3 FS on sda1, internal journal
[ 20.995804] EXT3-fs: mounted filesystem with ordered data mode.

e2fsck 1.41.0 (10-Jul-2008) /dev/sda2: recovering journal /dev/sda2: clean, 12/211744 files, 31151/846641 blocks

[ 21.233615] kjournald starting. Commit interval 5 seconds
[ 21.302741] EXT3 FS on sda2, internal journal
[ 21.354777] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.435149] ESS OSAL release
[ 21.471924] pal_linux: no version for "os_pci_get_device_address" found: kernel tainted.
[ 21.571106] PAL driver init...
[ 21.607476] PIC mode = 1
[ 21.637615] Device: CE4100
[ 21.670885] Stepping: B2
[ 21.703680] platform_config init complete! (build Aug 4 2010)
/* LOAD "/etc/platform_config/ce4100/memory_layout_512M.hcfg" to (new) database location "platform.memory.layout"*/

shifting platform_config media_base_address 700 MB ( 0x2bc00000 )

/* EXECUTE config database location "platform.startup"*/
[ 22.069841] ESS SVEN init:Aug 4 2010 15:50:06
[ 22.122869] /work/git/sdk-merge/git/project_build_i686/IntelCE/sven-13.9.10292.121182/driver/i686-linux-kernel/sven_linux_driver.c: 222: SVEN Header Initialized ac8f0000@2f000000:00001000, circbuf ac900000@2ef00000:00100000 dis:ffffffff
[ 22.373464] /work/git/sdk-merge/git/project_build_i686/IntelCE/sven-13.9.10292.121182/driver/i686-linux-kernel/sven_dfx.c: 242: SVEN DFX Enabled @df8f0000:00010000 wpos:0
[ 22.568711] SOC CE4100 found
[ 22.613195] Clock control: Probing external clock 'IDT_6V49061'...
[ 22.687200] Clock control: Clock 'IDT_6V49061' found, reading configuration...
[map( 0xdfb00000, 0x0007a000 ) = 0x734e6000]
[ 22.950285] Intel SMD Demux Ver2 Module built on Aug 4 2010 @ 15:56:07
[ 23.041375] Intel SMD Gen4 Viddec Module built on Aug 4 2010 @ 15:57:04
[ 23.375618] MFD FW version number: 0.8.28
[ 23.457275] Intel VPP driver built: Aug 4 2010 15:57:36
[ 23.502295] VPP: Verbosity Level: 1
[ 23.544936] VPP: Intel VPP FW using Gen4 Settings
[ 23.651364] Intel SMD Video Renderer Driver built on Aug 4 2010 @ 15:57:47.
[ 24.450434] Audio FW for DSP 0 Initialized. Built on Jul 16 2010:10:06:22
[ 24.450442]
[ 25.080107] Audio FW for DSP 1 Initialized. Built on Jul 16 2010:10:07:15
[ 25.080115]
[ 25.161268] Intel SMD Audio driver initialized. Built on Aug 4 2010 at 18:29:05.
[ 25.161279] Available Audio Codecs:
[ 25.290984] -Dolby Digital (AC3): Tensilica DD (AC-3) Decoder Library ver:1.7 API ver:1.15
[ 25.390674] -Advanced Audio Codec (AAC): aacPlus v2 (8-ch) Decoder Library ver:2.9-1 API ver:1.15
[ 25.497920] -MPEG: HiFi2 MP3 5.1-Channel Decoder Library ver:3.1 API ver:1.15
[ 25.584032] -Dolby Digital Compatible Output (DDCO): HiFi2 DD Compatible Output Library ver:1.1 API ver:1.12
[ 25.702626]
[ 25.732793] CLOCK_SEC_RST reports a 1 so SEC FW/HW are present
[map( 0xdf950000, 0x00010000 ) = 0x72cf2000]
[map( 0xdf950000, 0x00007000 ) = 0x72ceb000]
[ 25.985511] PWR: _icepm_register:WARNING: Device 'vidcap' not used in any defined power mode -- ignored
[ 26.097798] thermal init complete! (build Aug 4 2010)
[ 26.142004] major number =242
[ 26.180432] Audio DAC driver installed.
[ 26.260284] vidcap_ce4X00 error in __i2c_access: I2C read failure ret:0x1004 bus:0x1 dev:0x26 addr:0x0 len:2
[ 26.358605] vidcap_ce4X00 error in __recv: call to __i2c_access failed @ line 1880
[ 27.318118] usbcore: registered new interface driver snd-usb-audio
[ 27.376961] alsa_shim: module license 'unspecified' taints kernel.
SVEN Interactive: Built Aug 4 2010
Copyright 2006-2010 Intel Corporation All Rights Reserved
type help for a list of commands or quit
(ev): 32 (long):4 (int):4 (short):2 (char):1
SVEN-Header: ver: 'SVE2' disab: ffffffff debugfl: 00000000
: hdr_pa:2f000000 hdr_sz:00001000
: buf_pa:2ef00000 buf_sz:00100000 tx_pos:00000000
: dfx_pa:df8f0000 dfx_sz:00010000
sven> hdr disable: 0xffffffff -> 0x00000000
sven> hdr disable: 0x00000000 -> 0x00000004
sven> SVENLog default accepts all events
sven> tar: Removing leading '/' from member names
rm failed for /data/av_timing_logs/*, No such file or directory
rm failed for -f, No such file[ 30.801719] ADDRCONF(NETDEV_UP): eth0: link is not ready or directory
[ 42.758523] input: LogiMultitouchDevice as /class/input/input3
[ 43.005244] init: untracked pid 682 exited
[ 44.146396] input: tcpipremote as /class/input/input4
[ 44.306880] input: anymote as /class/input/input5