RF Signal Analysis - Revision history

Rjmendez: /* Sending our own data */

2017-10-18T20:50:12Z

Sending our own data

← Older revision		Revision as of 20:50, 18 October 2017
Line 73:		Line 73:
	== Sending our own data ==		== Sending our own data ==

	With this data we can now use a tool like the YARD Stick One to transmit our own packets to the device. I have posted the complete ~~the~~ code here. https://github.com/rjmendez/ShockCollar		With this data we can now use a tool like the YARD Stick One to transmit our own packets to the device. I have posted the complete code here. https://github.com/rjmendez/ShockCollar

Rjmendez: Rjmendez moved page Blind RF Signal Analysis to RF Signal Analysis

2017-08-07T00:50:39Z

Rjmendez moved page Blind RF Signal Analysis to RF Signal Analysis

← Older revision	Revision as of 00:50, 7 August 2017
(No difference)

Rjmendez at 00:50, 7 August 2017

2017-08-07T00:50:26Z

← Older revision		Revision as of 00:50, 7 August 2017
Line 1:		Line 1:
	This page will be to cover some basic ~~blind~~ RF signal analysis.		This page will be to cover some basic RF signal analysis.

	== About ==		== About ==

Rjmendez at 00:30, 7 August 2017

2017-08-07T00:30:23Z

← Older revision		Revision as of 00:30, 7 August 2017
Line 40:		Line 40:
	I know where to look for the signal now but the wave form isn't showing me very much. Listening to the demodulated audio does tell me something however, this sounds like Amplitude Shift Keying (ASK) also known as On Off Keying (OOK). Lets verify this with gnuradio and gr-fosphor over the hackrf for a bit higher quality signal.		I know where to look for the signal now but the wave form isn't showing me very much. Listening to the demodulated audio does tell me something however, this sounds like Amplitude Shift Keying (ASK) also known as On Off Keying (OOK). Lets verify this with gnuradio and gr-fosphor over the hackrf for a bit higher quality signal.

	[[File:Inspect_ook_grc.png]]		[[File:Inspect_ook_grc.png\|500px]]
	[[File:Inspect_ook_gr-fosphor.png]]		[[File:Inspect_ook_gr-fosphor.png\|500px]]

	This absolutely looks like OOK.		This absolutely looks like OOK.
Line 51:		Line 51:
	Our next task will be to determine the data rate, a favorite tool is Inspectrum (https://github.com/miek/inspectrum).		Our next task will be to determine the data rate, a favorite tool is Inspectrum (https://github.com/miek/inspectrum).

	[[File:Inspectrum_ook.png]]		[[File:Inspectrum_ook.png\|500px]]

	We can see the definite bits here and get a general idea about the baud rate, it looks like it is above 3500 baud but we can refine this! Another useful tool is Universal Radio Hacker (https://github.com/sthysel/urh) that can take a bunch of the work out of demodulating and decoding a signal.		We can see the definite bits here and get a general idea about the baud rate, it looks like it is above 3500 baud but we can refine this! Another useful tool is Universal Radio Hacker (https://github.com/sthysel/urh) that can take a bunch of the work out of demodulating and decoding a signal.

	[[File:URH_waveform_demod.png]]		[[File:URH_waveform_demod.png\|500px]]

	Knowing the approximate baud rate and our sample rate of 2 million samples per second we can start to fiddle with the bit length and noise level to decode the packets. Things start to settle out at 500 samples per bit. This would give us a baud rate of 4000, this isn't accurate because of the rest of the tinkering but it will let us decode the signal. More careful adjustment will get us closer to the actual rate of 555 samples per second or 3600 baud. At this point we can retransmit these bits with the hackrf and trigger the device but it doesn't give us a clear of an idea what is actually going on.		Knowing the approximate baud rate and our sample rate of 2 million samples per second we can start to fiddle with the bit length and noise level to decode the packets. Things start to settle out at 500 samples per bit. This would give us a baud rate of 4000, this isn't accurate because of the rest of the tinkering but it will let us decode the signal. More careful adjustment will get us closer to the actual rate of 555 samples per second or 3600 baud. At this point we can retransmit these bits with the hackrf and trigger the device but it doesn't give us a clear of an idea what is actually going on.
Line 61:		Line 61:
	The pattern of bits look like there is some error correction built in, a sequence of 1000 seems to equal 0 and 1110 equals a 1. URH will let us decode this further as seen below.		The pattern of bits look like there is some error correction built in, a sequence of 1000 seems to equal 0 and 1110 equals a 1. URH will let us decode this further as seen below.

	[[File:URH_NRZ_replace.png]]		[[File:URH_NRZ_replace.png\|500px]]

	The resulting packets now look like this.		The resulting packets now look like this.
Line 69:		Line 69:
	If we ignore the noise on 5 and 10 we can see a sequence forming. This sequence is the result of changing the power level setting on the remote control. With more changes and monitoring the entire protocol can be decoded.		If we ignore the noise on 5 and 10 we can see a sequence forming. This sequence is the result of changing the power level setting on the remote control. With more changes and monitoring the entire protocol can be decoded.

	[[File:Collar_protocol_packet.PNG]]		[[File:Collar_protocol_packet.PNG\|500px]]

	== Sending our own data ==		== Sending our own data ==

	With this data we can now use a tool like the YARD Stick One to transmit our own packets to the device. I have posted the complete the code here. https://github.com/rjmendez/ShockCollar		With this data we can now use a tool like the YARD Stick One to transmit our own packets to the device. I have posted the complete the code here. https://github.com/rjmendez/ShockCollar

Rjmendez: Rjmendez moved page User:Rjmendez to Blind RF Signal Analysis

2017-08-06T22:23:07Z

Rjmendez moved page User:Rjmendez to Blind RF Signal Analysis

← Older revision		Revision as of 22:23, 6 August 2017
(No difference)

Rjmendez: Created page with "This page will be to cover some basic blind RF signal analysis. == About == Many IoT devices use < 1Ghz signaling for various functions (various sensors, remote controls, dev..."

2017-08-06T22:21:42Z

Created page with "This page will be to cover some basic blind RF signal analysis. == About == Many IoT devices use < 1Ghz signaling for various functions (various sensors, remote controls, dev..."

New page

This page will be to cover some basic blind RF signal analysis.

== About ==
Many IoT devices use < 1Ghz signaling for various functions (various sensors, remote controls, device to device communication) with an undocumented and sometimes proprietary protocol. It can often be difficult to understand these without documentation and the aim here is to provide some of the first steps needed to identify and decode some of the data. The hardware used in this demo will be:

A HackRF from Great Scott Gadgets. (https://greatscottgadgets.com/hackrf/)

An RTL-SDR dongle from the rtl-sdr blog that is for sale on amazon. (http://www.rtl-sdr.com/buy-rtl-sdr-dvb-t-dongles/)

Another device from Great Scott Gadgets, the YARD Stick One. (https://greatscottgadgets.com/yardstickone/)

== Where to look ==

One great place to start is with the FCC documentation for the transmitting device, if the device has an fccid then it will have information on file. Some good reference links are below.

Awesome US spectrum allocation graphic: https://upload.wikimedia.org/wikipedia/commons/d/df/United_States_Frequency_Allocations_Chart_2011_-_The_Radio_Spectrum.pdf

Wikipedia page on ISM bands: https://en.wikipedia.org/wiki/ISM_band

Our demo device right now will be an alarm remote control with the fccid "B4Z-RF400401" that does not have the frequency listed on the package.

[[File:Remote.jpg|300px]]

We can throw this ID into the https://fccid.io/ site to get some details.

https://fccid.io/B4Z-RF4004-01-2

[[File:B4Z-RF400401_fccid.io.PNG|300px]]

Now we know where this device is supposed to be transmitting and we can move on to the next steps.

== How to look ==

Some favorites are gqrx (linux and mac http://gqrx.dk/) or sdr# (windows http://airspy.com/download/ ) in a higher sample rate mode to inspect the entire band the device operates on to look for the signal. For the rest of the demo I will be using another device with no FCC id. It advertises that it operates at 433mhz. I will be capturing with the RTL-SDR dongle.

[[File:Shock_Collar.jpg|300px]]

{{#ev:youtube|NI8U1IfQyto}}

I know where to look for the signal now but the wave form isn't showing me very much. Listening to the demodulated audio does tell me something however, this sounds like Amplitude Shift Keying (ASK) also known as On Off Keying (OOK). Lets verify this with gnuradio and gr-fosphor over the hackrf for a bit higher quality signal.

[[File:Inspect_ook_grc.png]]
[[File:Inspect_ook_gr-fosphor.png]]

This absolutely looks like OOK.

Useful link to the Signal Identification Guide wiki: http://www.sigidwiki.com/wiki/Signal_Identification_Guide

== Decoding ==

Our next task will be to determine the data rate, a favorite tool is Inspectrum (https://github.com/miek/inspectrum).

[[File:Inspectrum_ook.png]]

We can see the definite bits here and get a general idea about the baud rate, it looks like it is above 3500 baud but we can refine this! Another useful tool is Universal Radio Hacker (https://github.com/sthysel/urh) that can take a bunch of the work out of demodulating and decoding a signal.

[[File:URH_waveform_demod.png]]

Knowing the approximate baud rate and our sample rate of 2 million samples per second we can start to fiddle with the bit length and noise level to decode the packets. Things start to settle out at 500 samples per bit. This would give us a baud rate of 4000, this isn't accurate because of the rest of the tinkering but it will let us decode the signal. More careful adjustment will get us closer to the actual rate of 555 samples per second or 3600 baud. At this point we can retransmit these bits with the hackrf and trigger the device but it doesn't give us a clear of an idea what is actually going on.

The pattern of bits look like there is some error correction built in, a sequence of 1000 seems to equal 0 and 1110 equals a 1. URH will let us decode this further as seen below.

[[File:URH_NRZ_replace.png]]

The resulting packets now look like this.

[[File:Decoded_packets.png]]

If we ignore the noise on 5 and 10 we can see a sequence forming. This sequence is the result of changing the power level setting on the remote control. With more changes and monitoring the entire protocol can be decoded.

[[File:Collar_protocol_packet.PNG]]

== Sending our own data ==

With this data we can now use a tool like the YARD Stick One to transmit our own packets to the device. I have posted the complete the code here. https://github.com/rjmendez/ShockCollar